西安新敏干燥氣體微壓力變送器CYB11W系列微壓力變送器
產品簡介
CYB11W 系列微壓力變送器采用進口高精度、高穩定性微壓力敏芯片,經嚴格精密的溫度補償,線性補償,信號放大, V/I 轉換,逆極性保護,壓力過載限流等信號處理,將很微小的風壓流量等參數的轉換成工業標準的4~20mA或1~5VDC信號輸出。
該變送器可廣泛用于食品,環保,冶金,電力,輕紡,電子,醫藥等領域?qū)ιa(chǎn)過程中十分微小的非腐蝕性干燥氣體的壓力進行測量和控制?蓽y(cè) 10KPa以下的干燥氣體,最小量程可達100Pa,是超凈廠房和鍋爐自動化檢測的理想產品。
參數規格
量 程 范 圍 | 0~±100、500…1000(Pa) | 精 確 度 | ±0.3%F.S ±0.5%F.S ±1%FS |
0~±2、5、10(KPa) | 長 期 穩 定 性 | ≤±0.3%F.S/年 | |
過 載 壓 力 | ≤ 200%FS | 介 質 溫 度 | - 20~+85℃ |
測 量 介 質 | 非腐蝕性干燥氣體 | 響 應 時 間 | ≤1ms |
輸 出 信 號 | 4~20mA 二線制 | 壓 力 接 口 | Φ8塔型接口 |
1~5VDC 三線制 | 電 氣 接 口 | 電纜出線 | |
供 電 電 壓 | 12~36VDC (標定值為+24VDC) | 殼 體 材 料 | 1Cr18Ni9Ti或鋁合金 |
產品特點
●測非腐蝕性干燥氣體的風壓,流量
●可連續測量負壓和正壓
●靈敏度高,可測小于 100Pa 微小壓力
●精度高,穩定性好
●抗干擾設計
●體積小,安裝方便
外形結構
產品選型
CYB11W | 微壓力變送器 | ||||||
G | 表壓 | ||||||
0~X( Pa或KPa) | 量程 | ||||||
J03 | ± 0.3%FS | ||||||
J05 | ± 0.5%FS | ||||||
J10 | ± 1%FS | ||||||
C1 | 4~20mA輸出 | ||||||
C3 | 1~5VDC輸出 | ||||||
C0 | 特殊 | ||||||
M4 | Φ 8塔型接口 | ||||||
M0 | 特殊 | ||||||
F2 | 直接電纜出線 | ||||||
F0 | 特殊 |
PEWATRON傳感器,PEWATRON壓力傳感器、PEWATRON氣體傳感器、PEWATRON加速度傳感器、PEWATRON溫度傳感器、PEWATRON角度傳感器、PEWATRON行程傳感器
上海軼舜機電設備有限公司特價供應瑞士PEWATRON傳感器、PEWATRON壓力傳感器、PEWATRON氣體傳感器、PEWATRON加速度傳感器、PEWATRON溫度傳感器、PEWATRON角度傳感器、PEWATRON行程傳感器、PEWATRON距離傳感器、PEWATRON長度傳感器、PEWATRON扭矩傳感器、PEWATRON傾斜傳感器、PEWATRON電流傳感器、PEWATRON開關電源、不間斷電源、直流電機、軌跡球、操縱桿開關等。部分型號系列列舉:FPBS、FAM、FGM、FPM、FDM、FHM、FPN、FGN、PSM、XFPM、XFDM、XFHM、XFPN、XFGM、PSML、AG1、CP-2FK、CP-2FC-2、CP-2FB、CP-2FA、CP-2FA BS J-SW4、QP-3F、CP-3F、CPP-32SB、CP-3FB、CPP-35B、CPP-45B、CPP-60B、CPP-45 b.s.350°、CPP-45RB、CPP-45-..S、CP-2F-..S-RB、CP-2F-10S-RB-4、CP-2F-35S-RB-2、CP-2F-50S-RB-1、CP-2UTX-SW4、CP-2UT-SW4、CP-2UM-SW4、CP-UPX-SW4、CP-2UA-SW4、QP-2H-SW4、QP-3HBB-SW4、QP-3HB-SW4、CP-2HB-SW4、QP-2HC-2-SW4、DC-50E、DC-1000S、HDC-1000-EKC/S、HDC-20X、HDC-200-GS、HDC-50-ASE、FJX-W-SW7、HDC-300AHS、MSR 145、MIL-STD-810等等。
產品包括:PEWATRON傳感器、PEWATRON壓力傳感器、PEWATRON氣體傳感器、PEWATRON加速度傳感器、PEWATRON溫度傳感器、PEWATRON角度傳感器、PEWATRON行程傳感器
參數名稱 | 產品名稱 | 紅外煙氣氣體傳感器檢測模塊 | 11 | 檢測原理 | 紅外光度計, 氣體過濾 |
2 | 產品型號 | MGA09 | 12 | 精度 | < 2%檢測范圍 |
3 | 檢測氣體 | CO、NO、SO2、NO2、CO2、O2、H2O、CH4等 | 13 | 零點校正 | Modbus 控制 |
4 | 尺寸(W x H x D) | 392 mm x 92 mm x 83 mm注:1000ppm以上 300 mm x 350 mm x 110 mm 注:1000ppm以下 | 14 | 靈敏度校正 | Modbus 控制及校驗氣體 |
5 | 重量 | approx. 1kg | 15 | 壓力校正 | 內部 |
6 | 工作溫度 | 5 - 40℃ (氣溫需穩定) | 16 | 響應時間 | T90 < 180 s (依據氣體組分不同) |
7 | 存儲溫度 | 0 - 50℃ | 17 | 輸出信號 | 通過 Modbus 通信協議 * 零點和參考點的數字輸入信號 * 錯誤、配置以及維修要求的數字輸出信號 * 所有濃度的輸出 |
8 | 相對濕度 | 最大90% (非冷凝狀態) | 18 | 外部接口 | Modbus 通信協議 |
9 | 預熱時間 | 大約15 分鐘(環境溫度20℃下) | 19 | 電源 | 5 V DC / 6 A 穩定電源,1% 精確度(如Traco 電源TPM 30105) |
10 | 流量 | 0.8 - 1.2 L/min(推薦) | 20 | 可選配件 | 1個電化學氧氣傳感器 |
(可指定其他量程) | 1 | 一氧化碳CO | 0 - 200/1000 mg/m3 | 0 - 160/800 ppm | |
2 | 一氧化氮NO | 0 - 300/1000 mg/m3 | 0 - 225/750 ppm | ||
3 | 二氧化硫SO2 | 0 - 200/1000 mg/m3 | 0 - 70/350 ppm | ||
4 | 甲烷CH4 | 0 - 200/1000 mg/m3 | 0 - 280/1400 ppm | ||
5 | 氧氣O2 | 0 - 25 Vol. % | 電化學傳感器 | ||
6 | 二氧化碳CO2 | 0 - 25 % Vol.% | 用于校準補償 | ||
7 | H2O | 0 - 3 % Vol.% | 用于校準補償 |
4、鋼鐵熱處理氣氛控制系統
應用行業:電廠、冶煉廠、水泥廠、工業廢氣、煤粉倉等。
上海貴民實業發展有限公司供應德國倍朗BIELER+LANG氣體監控監測及報警系統 BIELER+LANG監測器 BIELER+LANG監控器 BIELER+LANG控制器 BIELER+LANG檢測器 BIELER+LANG傳感器 BIELER+LANG紅外氣體傳感器 BIELER+LANG防爆探測器 BIELER+LANG氣體報警器 BIELER+LANG開關
德國倍朗BIELER+LANG 公司由Bieler (Hermann Bieler) 和Lang (Karl-Heinz Lang)兩個家族合伙經營,創建于1967年,1969年開始發展氣體報警裝置業務,在1970年,就把氣體報警儀表推入了市場,其銷售網絡在1975年就覆蓋了整個德國。1982年,德國倍朗BIELER+LANG公司推出了第1批微電腦控制的氣體監測、報警和控制系統,1983年,一氧化碳(CO)檢測與報警儀進入了德國的地下停車場等場所。隨著科研開發的成功,儀表品質和性能日益完善和提高,品種越來越完善,即擴展到各種毒性氣體、易燃易爆氣體的監測和余氧測量與調節等,1984年開發了冗余氧氣監控計調節系統,在1985年,業務擴展到了整個歐洲。 1992年,德國倍朗BIELER+LANG公司開發出了第2代CO報警系統,1993年,家族由第二代即Thomas Springmann 和 Dipl-Ing. Heinz Lang主持經營公司,業務又發生了一次飛躍,1996年開發了取代模擬量控制的數字量控制系統,1997年德國倍朗BIELER+LANG通過了所有的歐洲防爆認證,于1998年,開發出第3代CO報警系統。2000年的時候, 通過了DIN EN ISO9001認證,2002年通過了PTB的ATEX 100A質量標準認證,超過40年的經驗,使得他們能夠非常專業地應付各種氣體監控和報警的任務,從而地保護人員健康、環境衛生和勞動安全,是客戶最信賴最安全的氣體監控監測及報警系統供應商。德國倍朗BIELER+LANG公司不斷地自行研究、開發,并嚴格按照高質量標準生產,使得該公司的儀表操作非常簡單、性能極為。德國倍朗BIELER+LANG在海關的商品檢驗部門、大學實驗室和科研機構,化工行業,煉油行業,鋼鐵冶金行業,煤電行業,鼓風爐,軋鋼廠,造紙,紡織,皮革,采礦,汽車制造,車輛修理,地下停車場,隧道,地道,橡膠加工,污水處理,泳池,水凈化,塑料工業等領域有廣泛。 型號如: BIELER+LANG EXDETECTOR HC-100M , BIELER+LANG CONTROLLER GMC8364, BIELER+LANG GASMESSCOMPUTER 8022 GMC8022E, BIELER+LANG EXDETECTOR HC-100K, BIELER+LANG EXDETECTOR HC-100T, BIELER+LANG EXDETECTOR HC-200, BIELER+LANG GASMONITOR HC66, BIELER+LANG GASMONITOR CO, BIELER+LANG GASMONITOR H2S, BIELER+LANG GASMONITOR NO, BIELER+LANG GASMONITOR NO2, BIELER+LANG GASMONITOR SO2, BIELER+LANG GASMONITOR Cl2, BIELER+LANG GASMONITOR HCN, BIELER+LANG GASMONITOR H2, BIELER+LANG GASMONITOR HCl, BIELER+LANG GASMONITOR NH3, BIELER+LANG GASMONITOR O3, BIELER+LANG GASMONITOR C2H40, BIELER+LANG GASMONITOR O2 , BIELER+LANG EXMONITOR CO, BIELER+LANG EXMONITOR H2S, BIELER+LANG EXMONITOR NO, BIELER+LANG EXMONITOR NO2, BIELER+LANG EXMONITOR SO2, BIELER+LANG EXMONITOR Cl2, BIELER+LANG EXMONITOR HCN, BIELER+LANG EXMONITOR H2, BIELER+LANG EXMONITOR HCl, BIELER+LANG EXMONITOR NH3, BIELER+LANG EXMONITOR O3, BIELER+LANG EXMONITOR C2H40, BIELER+LANG EXMONITOR O2 , BIELER+LANG EXDETECTOR SC-220, BIELER+LANG GASALARM 7011, BIELER+LANG GASALARM 7012, BIELER+LANG GASMESSCOMPUTER 7021, BIELER+LANG GASMESSCOMPUTER 7022, BIELER+LANG GMC 7022E, BIELER+LANG GASMONITOR CO-300, BIELER+LANG GASMONITOR NO2-300, BIELER+LANG GASMESSCOMPUTER 8022-CO, BIELER+LANG GMC 8022E-CO, BIELER+LANG GASMONITOR CO-500, BIELER+LANG GMC ECOLINE 8304, BIELER+LANG GM ECOLINE HC50…
introduction cyber®-tx is a microprocessor based pcb product, designed for gas sensing applications. it may be used together with a co or h2s lectrochemical cell, a catalytic gas sensor for flammable gases, or an infrared sensor for co2 or hydrocarbon gases and vapours. the raw signal input from the sensor is processed digitally by the microprocessor, which also stores information such as calibration data, the range and lifetime of the sensor. the device can be configured to deliver the sensor readings as linear analogue outputs (0.4-2v or standard 4-20ma). cyber®-tx can also be interrogated digitally via rs485, with information such as alarm thresholds, fault conditions, calibration information etc being available from the microprocessor’s registries.structurecyber®-tx is built around a 12bit microcontroller. it provides analogue outputs and a serial output rx/tx to facilitate communication.a number of versions of the device are available, depending on the gas sensor with which it is being used: - catalytic sensor (single or matched pair) for combustible gases detection;- electrochemical cell for toxic gas detection;- infrared (ir) sensor for co2 and/or hydrocarbon detection.various circuits are implemented in accordance with the sensor used and the application:- the self test circuit (for the co cell);- zero drift compensation circuit.operation the main board is provided with some basic information written in the microprocessor’s memory:- lot/serial number- calibration date- span factor (for catalytic sensor)- alarm thresholdsall the above are written in the registries and are available for reading using the digital output.other output data available:- the present measured gas concentration on demand (in ppm or %lel depending on the sensor used)- alarm condition- fault condition- the age of the sensor (depending on the application)according to the board version, through the respective protocol, all the above in formation is available for readout.a 0.4 - 2v analogue voltage signal is also included as standard.a standard 4 - 20ma current output is also available for remote analogue monitoring purposes, using an optional second pcb, allowing cyber®-tx to be used as a simple 4 – 20ma transmitter if required.notes:1. span/rank - for a catalytic gas sensor, monitoring combustible gases, the relative esponse of the target gas is used to determine the range of the device.the readout drift in gas is memorized as the span, together with the zero value when calibrating the device.for some electrochemical cells, a rank se-lection gives the drift in na/1ppm of co detected.the span or rank respectively, depending on the application, is memorized in the icroprocessor’s registries.2. lifetime - the lifetime of the electrochemical cell is usually 2-5 years, depending on the manufacturer specifications, provided the measured output does not fall bellow a certain percentage of the original output. the microprocessor’s software is provided with atimer, counting the time elapsed from the sensor’s first calibration. a fault signal is rovided on the serial output after the programmed number of years, stating that cell should be replaced.3. auto-zero – the drift of the zero indication in time affects the reading of the actual gas level so it is automatically compensated.the software implemented contains a routine which compensates for the drift in zero level.4. self-test – for the co electrochemical cells, as defined by standards, a self test routine is included, which monitors the sensor’s electrodes for short circuit or open circuit faults. the microprocessor will indicate a short or open circuit by means of the on-board fault signal.also, in case of electrolyte leakage in significant quantity or in case of complete drying of electrolyte, the self test will activate a fault output to warn of the imminent failure of the cell.(n.b. – the function is available on the nemoto electrochemical cells only)5. ack/peak – an input is provided instead of alarm 2 to acknowledge the alarm signal, if requested or to provide the peak concentration level from the last acknowledgement on.6. buzzer – an output is provided instead of alarm 1 for a buzzer if necessary.pin desc-riptionif provided with main board only, the pin assignment is as in the upper drawing.
產品特點:
MS1100-P111傳感器是一款原裝進口的半導體式VOC氣體傳感器,具有極高的靈敏度和穩定性,能夠偵測0.1ppm以上的氣體,適用于檢測空氣中的甲醛、苯、二甲苯等多種有機揮發成分,同時具有體積小巧、價格便宜、響應速度快等特點。
北京時陽電子科技有限公司
Q Q:2119841551
網址:http://www.bjsydz.com/
PID光離子氣體傳感器PID-AH2(小量程)
一、 PID-AH2氣體傳感器產品簡介: 許多有害物質原料都含有VOC,PID由于其對VOC的高靈敏度,成為有害物質早期危險報警、泄漏監測等不可缺少的實用工具。 目前通過對燈泡以及內部IC升級,大大延長了燈泡的使用壽命。
二、PID-AH2氣體傳感器主要特性: 1、 A系列標準尺寸,帶有微型聚光光源。 2、 測量范圍:1ppb-50ppm3、 工作環境,-40~55℃,相對濕度0-95% 4、 供電電壓:3.2-3.6V(調節器未用);3.2-10.0V(調節器使用) 5、 輸出電壓:零點(>46 mV)~Vmax(供電電壓-0.1V @調節器使用)6、 功耗,85mW(3.2V供電)7、 過載:50ppm(以異丁烯參考) 8、 在自由擴散情況下響應時間小于3秒 9、 使用壽命大于5年(不含UV燈和柵極)10、 A系列標準尺寸插針